Torrex™ Flameshield Ultimate-AG


The Torrex™ Flameshield Ultimate-AG system allows you to upgrade the fire rating of existing painted surfaces (subject to adhesion), protecting against rapid spread of flame and graffiti. The 3-coat system has been successfully tested on the Warrington Blue Board and is covered under the Certifire 3rd Party accreditation scheme, giving specifiers peace of mind. Our systems allow proprietors to comply with Section B2 of the building regulations and fulfil their obligations under the Regulatory Reform (fire safety) Order (RRFSO).

The topcoat is an anti-graffiti finish which offers superior levels of protection against damage by allowing long-term graffiti removal when used in conjunction with the Tor graffiti removal systems.



      • Designed for previously painted surfaces
      • True three coat Class 0 fire upgrading system
      • Certifire approved
      • Upgrades Exova Warringtonfire Class 4 ‘Blue Board’ to Class 0
      • Superb graffiti removal properties
      • Low textured, gloss finish
      • Fast installation
      • Free from antimony and brominated compounds
      • Can be applied in low temperatures
      • Comprehensive colour range


Frequently Asked Questions

1st Coat
Torrex™ Ultimate Primer (EP111), a two-pack primer for use on well adhered previously painted surfaces.

2nd Coat
Torrex™ Flameshield Ultimate Buildcoat (EM375) a single-pack, high build, textured coating that adds fire protection to the system.

3rd Coat
Torrex™ Ultimate-AG (EP288 ) a two-pack, solvent free, fire upgrading coloured finish with unparalleled graffiti removal properties.

Previously painted internal plaster and plasterboard, brick, masonry, concrete, ceramic tiles. The previously painted areas must be well adhered.

Torrex™ Flameshield Ultimate-AG is suitable for all well adhered internal surfaces where effective protection from rapid flame spread and graffiti is needed. Typical areas include walls and ceilings in the following locations:

  • Communal areas, landings and lift lobbies in social housing blocks
  • Internal fire escape areas
  • Internal public access areas
  • Toilet blocks in schools and public conveniences
  • Corridors and escape routes in public buildings including schools, colleges, hospitals, nursing homes, leisure centres, community centres and office blocks

Graffiti can be safely and easily removed from all of the Tor Coatings anti-grafitti range by using the Torclean™ Pre-Wipe (SS454001) and Torclean™ Graffiti Remover Wipe (SS455001) or by using the Torclean™ Graffiti Pre-Wash (DM416) and the Torclean™ “G” Graffiti Remover (DM424).

Only Tor Coatings remover wipes and sprays should be used as other materials may damage the painted surface, resulting in system failure and permanent graffiti damage.

The use of abrasive pads and household detergents should never be considered unless otherwise instructed by a representative of Tor Coatings Ltd.

  • Unrivaled expertise and knowledge
  • Nationwide team of area managers / technical personnel
  • Free site survey
  • Free specification service (find us on NBS Plus)
  • On-site technical back-up for live projects
  • CPD seminar ‘Understanding the control of rapid flame spread in building refurbishment’ available
  • Comprehensive guarantees available

The following specification is included for demonstrative purposes only and would be suitable for use over well adhered existing coatings. Always consult a representative of Tor Coatings prior to specifying or applying.

Torrex™ Ultimate Primer

By brush or medium pile roller, apply one full coat of Torrex™ Ultimate Primer (EP111) at a coverage rate of 13.33m² per litre. Allow to dry.

Torlife™ Flameshield Ultimate Buildcoat

By brush or medium pile roller, apply one full coat of Torlife™ Flameshield Ultimate Buildcoat (EM375) at a theoretical coverage rate of 1.33m² per litre. Immediately after application and whilst the coating is still wet, lightly roll over the whole of the coated area with a foam texturing roller to produce an even, light texture effect. Allow to cure. Overcoating time minimum 16 hours, maximum 7 days.

Torrex™ Ultimate AG Finish

By brush or short / medium pile roller, apply one full coat of Torrex™ Ultimate AG Finish (EP288) at a theoretical coverage rate of 13m² per litre. Allow to cure.

Tor Coatings offers a free site survey service and all of our Area Business Managers are fully trained and able to carry out full site assessments. A detailed and bespoke specification will then be issued.

Contact Tor Coatings on 0191 410 6611 to arrange your free site survey.

Tor Coatings’ national team of Area Business Managers is supported by a dedicated customer services team, a team of experienced paint chemists and a dedicated technical help desk. Call 0191 411 3148 for assistance from our helpdesk or visit to find out more.

Can’t find what you are looking for?

Click here to contact us or call us today on 0191 410 6611

Fire extinguisher in empty white corridor

Get in touch

Click here to arrange a FREE site survey
or call us on 0191 410 6611