Tor Coatings is pleased to announce its recent registration with the Achilles Link Up scheme. Achill…Read more
* Compared with other Class 0 upgrading systems needing more coats
Torrex™ Flameshield Ultimate-AG allows you to upgrade the fire rating of existing well adhered painted surfaces, protecting against rapid spread of flame and graffiti. This three coat system successfully upgrades the Exova Warringtonfire Class 4 ‘Blue Board’ to Class 0 when tested to BS476 Parts 6 & 7.
This coating system is Certifire approved and helps specifiers and building managers comply with Section B2 of the Building Regulations and fulfill their obligations under the Regulatory Reform (Fire Safety) Order (RRFSO).
The topcoat is an anti-graffiti finish which offers superior levels of protection against serious abuse by allowing long-term, effective graffiti removal when used in conjunction with the Tor graffiti removal systems.
Torrex™ Ultimate Primer (EP111), a two-pack primer for use on well adhered previously painted surfaces.
Torrex™ Flameshield Ultimate Buildcoat (EM375) a single-pack, high build, textured coating that adds fire protection to the system.
Torrex™ Ultimate-AG (EM288) a two-pack, solvent free, fire upgrading coloured finish with unparalleled graffiti removal properties.
Previously painted internal plaster and plasterboard, brick, masonry, concrete, ceramic tiles. The previously painted areas must be well adhered.
Torrex™ Flameshield Ultimate-AG is suitable for all well adhered internal surfaces where effective protection from rapid flame spread and graffiti is needed. Typical areas include walls and ceilings in the following locations:
The following specification is included for demonstrative purposes only and would be suitable for use over well adhered existing coatings. Always consult a representative of Tor Coatings prior to specifying or applying.
By brush or medium pile roller, apply one full coat of Torrex™ Ultimate Primer (EP111) at a coverage rate of 13.33m² per litre. Allow to dry.
By brush or medium pile roller, apply one full coat of Torlife™ Flameshield Ultimate Buildcoat (EM375) at a theoretical coverage rate of 1.33m² per litre. Immediately after application and whilst the coating is still wet, lightly roll over the whole of the coated area with a foam texturing roller to produce an even, light texture effect. Allow to cure. Overcoating time minimum 16 hours, maximum 7 days.
By brush or short / medium pile roller, apply one full coat of Torrex™ Ultimate AG Finish (EP288) at a theoretical coverage rate of 13m² per litre. Allow to cure.
Tor Coatings offers a free site survey service and all of our Area Business Managers are fully trained and able to carry out full site assessments. A detailed and bespoke specification will then be issued.
Contact Tor Coatings on 0191 410 6611 to arrange your free site survey.
Tor Coatings’ national team of Area Business Managers is supported by a dedicated customer services team, a large team of paint chemists and a dedicated technical help desk. Call 0191 411 3148 for assistance from our helpdesk or email firstname.lastname@example.org
Graffiti can be safely and easily removed from all of the Tor Coatings anti-grafitti range by using the Torclean™ Pre-Wipe (SS454001) and Torclean™ Graffiti Remover Wipe (SS455001) or by using the Torclean™ Graffiti Pre-Wash (DM416) and the Torclean™ “G” Graffiti Remover (DM424).
Only Tor Coatings remover wipes and sprays should be used as other materials may damage the painted surface, resulting in system failure and permanent graffiti damage.
The use of abrasive pads and household detergents should never be considered unless otherwise instructed by a representative of Tor Coatings Ltd.
|Torrex Ultimate Primer||Torrex F/shield Ultimate Buildcoat||Torrex Ultimate AG finish|
|Theoretical Coverage||13.33m2 per litre||1.33m2 per litre||13m2 per litre|
|Application||Brush/medium roller||Brush/medium roller||Brush/medium roller|
|Pack Size||5 litres||10 litres||5 litres|
|Touch Dry||4 hours||4 hour||4 hour|
|Hard Dry||16 hours||16 hours||16 hours|
|Minimum overcoating time||16 hours||16 hours||N/A hours|
|Maximum overcoating time||7 days||7 days||N/A|
This coating system is approved by Certifire. It has been independently ‘blue board’ tested by Exova Warringtonfire.